Forum Discussion

sameerjade's avatar
sameerjade
Frequent Contributor
6 years ago

Running tests from TestExecute using batch file

Hi! I created some smoke tests for our desktop application using TestComplete. I want to integrate these tests with TeamCity as part of continuous integration. I created a batch file which will run ...
  • sameerjade's avatar
    sameerjade
    6 years ago

    Thanks, Alex. I will try what you suggested with the additional quotes. I was able to solve the issue by calling the tasskill command between my tests to force close the TestExecute.exe application. It is probably not a very graceful solution but it is working for now. I will try with additional quotes too.

     

    Regards,

    Sameer

sameerjade's avatar
sameerjade
Frequent Contributor

Hi Alex,

 

Thank you for your reply. I tried using start /wait at the start of my command (sample attached below). When I run the batch file, it launches TestComplete and then nothing happens; it does not run the tests. Maybe because of '/wait'? Am I using the command correctly?

 

If I launch TestExecute and then right click the TE icon on bottom right corner and select Run>'myProject' (i.e. without a batch file), it runs my tests ok. Only when I run the batch file, I am running into the issue.

 

start /wait "C:\Program Files (x86)\SmartBear\TestExecute 12\Bin\TestExecute.exe" "C:\svn\TestComplete\DataPrepNew\DPSmokeTest\Reg360\Reg360.mds" /run /project:Reg360 /test:"Smoke Tests|Clean up" /ErrorLog:C:\Reg360_smoke_tests\Export_Logs\SmokeTestsErrorLog /exit /SilentMode /ExportLog:C:\Reg360_smoke_tests\Export_Logs\SmokeTests_log.html /ExportSummary:C:\Reg360_smoke_tests\Export_Logs\SmokeTestsSummary /Timeout:3600

 

start /wait "C:\Program Files (x86)\SmartBear\TestExecute 12\Bin\TestExecute.exe" "C:\svn\TestComplete\DataPrepNew\DPSmokeTest\Reg360\Reg360.mds" /run /project:Reg360 /test:"Smoke Tests|SmokeTest01TransgasE57import" /ErrorLog:C:\Reg360_smoke_tests\Export_Logs\SmokeTestsErrorLog /exit /SilentMode /ExportLog:C:\Reg360_smoke_tests\Export_Logs\SmokeTests_log.html /ExportSummary:C:\Reg360_smoke_tests\Export_Logs\SmokeTestsSummary /Timeout:3600

 

Regards,

Sameer

AlexKaras's avatar
AlexKaras
Champion Level 3
6 years ago

Hi Sameer,

 

> When I run the batch file, it launches TestComplete and then nothing happens; it does not run the tests.

Yes, indeed, it looks like everything after /wait must be one command. And this command will be parsed later by separate copy of command processor.

To get the above, your command line must be additionally quoted with proper number of quotes to met parsing rules. Try to surround the command in the batch file with additional quotes and check command processor's output to set quotes properly.

You may try to start with the line like this:

start /wait """C:\Program Files (x86)\SmartBear\TestExecute 12\Bin\TestExecute.exe" "C:\svn\TestComplete\DataPrepNew\DPSmokeTest\Reg360\Reg360.mds" /run /project:Reg360 /test:"Smoke Tests|Clean up" /ErrorLog:C:\Reg360_smoke_tests\Export_Logs\SmokeTestsErrorLog /exit /SilentMode /ExportLog:C:\Reg360_smoke_tests\Export_Logs\SmokeTests_log.html /ExportSummary:C:\Reg360_smoke_tests\Export_Logs\SmokeTestsSummary /Timeout:3600""

 

  • sameerjade's avatar
    sameerjade
    Frequent Contributor
    6 years ago

    Thanks, Alex. I will try what you suggested with the additional quotes. I was able to solve the issue by calling the tasskill command between my tests to force close the TestExecute.exe application. It is probably not a very graceful solution but it is working for now. I will try with additional quotes too.

     

    Regards,

    Sameer