Forum Discussion

kahmaui808's avatar
kahmaui808
Occasional Contributor
8 years ago

How Clear TestStep Values using TearDown Script

I have two projects. Project 1 is encrypted and has all the values for Project 2.   Project 2 runs and retrieves the values from Project 1, executes the tests and then I need Project 2 to get rid o...
  • Radford's avatar
    Radford
    8 years ago

    I'm not sure if this is any help, but...

     

    [Edit: Amended script after comments below]

     

    I took a look at this and came up with the following project teardown script:

     

    project.getTestSuites().each {testSuiteName, testSuite ->
	log.info('Test Suite: ' + testSuiteName)
	testSuite.getTestCases().each{testCaseName, testCase ->
		log.info('Test Case: ' + testCaseName)
		testCase.getTestSteps().each{testStepName, testStep  ->
			log.info('Test Step: ' + testStepName)
			if(testStep in com.eviware.soapui.model.TestPropertyHolder){
				testStep.getProperties().each{propName, prop ->
					if(!prop.isReadOnly()){
						// You may want to only remove properties based on property name here...
						log.info('Initial: ' + propName + ' = ' + prop.getValue() )
						prop.setValue('')
						log.info('Removal: ' + propName + ' = ' + prop.getValue() )
					}
				}
			}
		}
	}
}pre>

     

    Interestingly I also saw that while some were removed with some properties not marked as read only they would not be removed, no error was raised either.

     

    As a side note, this script is quite brutal in the way it attempts to remove all properties including all the ones that configure the test step, did you really want to do this or was it specific properties you wanted to remove?

kahmaui808's avatar
kahmaui808
Occasional Contributor

Thanks, but it didn't work. testRunner is not available in the TearDown. Is there a way to make testRunner available in the TearDown or can Runner be used?

 

I'm trying to remove all the user data and apiKey information from the project after successful test execution. If someone were to pull down the unencrypted project, they should not see any user data or apiKeys. I don't want to encrypt the project because I want to keep the composite project structure (encrypting forces a single project structure).

 

 

Radford's avatar
Radford
Super Contributor
8 years ago

After reading the comments I have amended my script to run as a project teardown script.

 

IMPORTANT: Before testing this script I recommend that you make sure you have a back up, if you start deleting properties you didn't mean to you may end up in a real mess.

  • nmrao's avatar
    nmrao
    Champion Level 3
    8 years ago
    kahmaui808, please pay attention to the NOTE/WARNING of Radford.

    By the way I would suggest in that case is to define the exclude property list in the script (better way) if less properties and clear the values conditionally. If there are too many properties to exclude, then you use include list and clear only those property values. Decide which one suites better for you.

    say sudo code:
    def excludeList = ['name1', 'name7']
    if current property name not in the excludeList, then only clear.

    This way, you do not have worry at all.
    • kahmaui808's avatar
      kahmaui808
      Occasional Contributor
      8 years ago

      Thank you! After looking at both of your suggestions I was able to get the script to run as a project level Tear Down.

       

      I did run the script "as is" to see how bad it would be if I removed all the properties... :) It was pretty bad.

       

      Luckily I made a backup as you both suggested.

       

      I created an "if" statement to just target the apiKey, but I like the solution to use the exclude list and will probably try that instead.

       

      You guys (nmrao and Radford) are awesome! Thank you for all the help!