Ask a Question

Parameters are greyed out

tobenschain
Occasional Contributor

Parameters are greyed out

Why are my AQtime|Parameters menu command greyed out?

9 REPLIES 9
AlexKaras
Champion Level 3

Hi,

 

Assuming that you have project created and profiled application been specified, what profiling mode has been set?

As per https://support.smartbear.com/viewarticle/43083/ : "You can specify run parameters for all profiling modes, except for the Service mode."

The more information (including screenshots) you provide about your problem, the higher chances to get a helpful piece of advice.

Regards,
  /Alex [Community Champion]
____
[Community Champions] are not employed by SmartBear Software but
are just volunteers who have some experience with the tools by SmartBear Software
and a desire to help others. Posts made by [Community Champions]
may differ from the official policies of SmartBear Software and should be treated
as the own private opinion of their authors and under no circumstances as an
official answer from SmartBear Software.
The [Community Champion] signature is assigned on quarterly basis and is used with permission by SmartBear Software.
https://community.smartbear.com/t5/Community-Champions/About-the-Community-Champions-Program/gpm-p/252662
================================
tobenschain
Occasional Contributor

The AQtime parameters are disabled again in Delphi XE7. What causes it? I will need to set them. I am using the Allocation Profiler.

 

Thanks

Tom

tobenschain
Occasional Contributor

here is a screen capture:

 

 

Hi,

 

Same question: what profiling mode (not profiler, but profiling mode) is set?

https://support.smartbear.com/viewarticle/43009/ (last paragraph) mentions how to check/set it in Delphi.

Also https://support.smartbear.com/viewarticle/43083/ might help.

Regards,
  /Alex [Community Champion]
____
[Community Champions] are not employed by SmartBear Software but
are just volunteers who have some experience with the tools by SmartBear Software
and a desire to help others. Posts made by [Community Champions]
may differ from the official policies of SmartBear Software and should be treated
as the own private opinion of their authors and under no circumstances as an
official answer from SmartBear Software.
The [Community Champion] signature is assigned on quarterly basis and is used with permission by SmartBear Software.
https://community.smartbear.com/t5/Community-Champions/About-the-Community-Champions-Program/gpm-p/252662
================================
tobenschain
Occasional Contributor

the buttons are greyed out. see attached

Hm-m... No ideas at the moment, sorry.

Try to contact Support via the https://support.smartbear.com/message/?prod=AQtime form, reference this thread and see what the reply will be.

Regards,
  /Alex [Community Champion]
____
[Community Champions] are not employed by SmartBear Software but
are just volunteers who have some experience with the tools by SmartBear Software
and a desire to help others. Posts made by [Community Champions]
may differ from the official policies of SmartBear Software and should be treated
as the own private opinion of their authors and under no circumstances as an
official answer from SmartBear Software.
The [Community Champion] signature is assigned on quarterly basis and is used with permission by SmartBear Software.
https://community.smartbear.com/t5/Community-Champions/About-the-Community-Champions-Program/gpm-p/252662
================================
tobenschain
Occasional Contributor

thanks, i just needed to open the aqtime profiler in project manager

Hi,

 

Thank you for the update.

All this thread is for AQtime Pro, not the version shipped with Delphi, right ?

Regards,
  /Alex [Community Champion]
____
[Community Champions] are not employed by SmartBear Software but
are just volunteers who have some experience with the tools by SmartBear Software
and a desire to help others. Posts made by [Community Champions]
may differ from the official policies of SmartBear Software and should be treated
as the own private opinion of their authors and under no circumstances as an
official answer from SmartBear Software.
The [Community Champion] signature is assigned on quarterly basis and is used with permission by SmartBear Software.
https://community.smartbear.com/t5/Community-Champions/About-the-Community-Champions-Program/gpm-p/252662
================================
tobenschain
Occasional Contributor

<<All this thread is for AQtime Pro, not the version shipped with Delphi, right?>>

yes

cancel
Showing results for 
Search instead for 
Did you mean: