Contributions
- 2.9KViews0likes1Comment
Re: QAComplete and test run. Gap in test execution
Howdy Tom, thanks for the reply and sharing your info as well... in my case I don't "think" its the same situation as per an experiment I tried: so, I began to wonder if it was QAComplete... or TestComplete... etc... I created a collection of the exact same tests... in the exact same order.... and ran using ONLY TestComplete this time and NOT QAComplete.... the entire suite/collection, ran, in approx 3.5 hours!!!! Perfect!!!! Not one test did NOT run, and not one test took anything near over 10-15 minutes... so, they ran as they should. So, what I know so far, when running using QAComplete... I have issues and that same suite of tests will take easily over 12 to 14 hours (!!!) ... whan running only using TestComplete, as ran as it should. I will run that same suite again, this evening, using only TestComplete again and see if it still runs as expected... under 4 hours, no tests missing. So, so far, "seems" Might be an Issue with QAComplete and my tests... Have not logged a bug yet... wanted to see if I could gather more info....2.9KViews0likes0CommentsRe: QAComplete and test run. Gap in test execution
So, still not sure what is happening. Anyone else seeing this? Every night now... random tests... out of 50, at 3 or 4, show in QAComplete as taking well over 2-3 hours.... but, no info in the log, I have no way to see what is happening. The test before and the one after, all show fine. Then, in TestComplete itself, the logs.... do NOT even show those Long running tests (thave have no log at all in QAComplete). For example, If I have: Test1 Test2 Test3 thru Test 50 Each test normally runs for 10 mins... and their log (pass or fail) can be seen in QAComplete run history and of course in TestComplete At random, I may see (In QAComplete) as an example: Test1 - Started and completed (09:00/09:10) Test2 - Started and Completed (09:10 / 09:21) THEN: Test3 - Started and Completed (09:22 / 13:01) - Over 3hours!!!! Test4 - Started and Completed (13:02 / 13:11) etc etc... QAComplete displays result for all the above... but says no records for that 3+ hour run! TestComplete does not show a log at all for Test3 (the 3+ hour run) In TestComplete I hav logs for all tests, except the ones that run for a ridiculous length of time.... its like they didnt even exist. Next time i run, those tests (e.g. Test3) will run flawless and the same problem will occur with a different test(s) I can't even see a log to see what the heck is happening... Lol Any ideas? Thanks again!2.9KViews0likes4CommentsRe: QAComplete and test run. Gap in test execution
Hmmm, I'll have to check into that.... its just really strange... like last nights run, again, a random test... shows it "ran" for almost" 3 hours.... but, in QAComplete, no results... so I can't see what may have happened.... and in TestComplete... under results, that test is not even listed??? But, next run, changing nothing... runs fine and dandy.3KViews0likes5CommentsQAComplete and test run. Gap in test execution
Howdy folks... ok, have a suite of about 60 tests.... have them scheduled... and executed on remote system.... In the past few weeks... I have noticed an extra long test execution timen for the suite... the suite should run in about 17 hours.... but has been running over 27 hours etc.... Upon investigation, I see, ,randomly, and nor repeatable at will... I see soem tests taking... 2 hours to run, these are 10 to 15 minute tests... but they show show as taking over 2 hours... My last run had 59 tests... but 5 of these took over 2-3 hours,,, again, should only take 10 to 15 mins. I have been unable to determine why yet... it is random tests and times so its not the same tests, and time of day... its random. In QAComplete the log displays nothing for those tests when it happens... all tests before and after, fine and dandy log shows info.... but for the ones that appear to go into the twilight zone... log contains no data. I look for the test log for these tests in TEST COMPLETE and there is nothing there... those tests dont show.... when that happens to them. And yes, the next run... next night, those same tests will run fine and it will happen to a handful mof other tests.... Strange.3KViews0likes9CommentsNo Log File - No Results????
Am running TC12 now, but even when running TC11... same issue. I have suite of tests that run well over 8 hours... So I kick 'em off... watch them running for a few hours... they are still running when I leave for the night..,. come in in the morning... see the App Under Test is still up... but... TestComplete is NOT up. So, I bring it up... no log, no results no anything... like it never ran??? This happens... frequently now in the past 2-3 months... more often than not. I have no idea how the tests ran and need to re-run again, sometimes several times or in "Chunks" if you will. Basically I kick them off as a project.... containing about 80 tests. Any help appreciated. Ron1.8KViews0likes6CommentsRe: TestComplete 12 Upgrade v fresh install... something "different"?
Howdy,tried Repair and back to the problem of not being able to use SPY (as I also accepted and performed the update that was immediately available) as appropriate. It does NOT recognize certain objects. Long story short... I uninstalled Java again,,,, re-ran repair again, Did NOT accept immediate update Now, all runs great again. BUT... without that immediate UPDATE (which caused the SPY issues) and without JAVA 1.8 So... something still not right.1.2KViews0likes0Comments